Three Phase (3PH) 3-Leg
REVO I 3PH – 3 Phase Unit to drive 3 phase load
REVO I 3PH
Technical Specification
- Operating Temperature: 0-40°
- Voltage Power Supply: 480V & 600V Max.
- Auxiliary Power Supply: 110V / 220V / 415V AC
- Fan Voltage supply: 230V ±15% as a standard and 110V on request
- Analog Input 1: Primary reference - Current Input 0-20mA / 4-20mA - Voltage Input 0-10V - Potentiometer Input 10K Ohm min
- Analog Input 2: External Current Limit, External feedback, alternate Setpoint
- Digital Input: Two optoisolated digital input (12/24V DC), for Enable, SP AI1/ AI2, local / remote, heater bakeout, Alarm reset
- Alarm Digital Output: Heater Break, Short circuit, Current Limit, SCR over temperature, watch dog, Relay Output
- Firing: Soft Start + Phase Angle / Burst firing / Zero cross over
- Soft Start Control: Digital adjustable ramp rate can be used
- Control Feedback Mode: V/ V2/ I/ I2/ Vxl
- Fuses: High speed Semiconductor fuses fitted Internally
- Mounting: Panel mounting
- Protection: IP20
REVO S 3PH Three phases static relay
REVO S 3PH
- From 30 up to 800A
- Voltage Range 480V, 600V and 690V
- Load type: Resistance, IR Lamp long and medium waveform
- Inputs: SSR Std, 0:10V, 4:20mA and Heather Break alarm are options
- Firing mode: Zero Crossing, Burst Firing available with analogue input only
REVO C 3PH – Revo Connect Universal SCR Power Controller Three Phases
REVO C 3PH
- Phases: 3
- Current Range from 30 to 2100A.
- Voltage Range 480V, 600V and 690V.
- Inputs: 4:20mA, 0:10V, SSR and ModBus as std and different Field Bus Listed in the Product Coding
- Firing mode: Burst Firing, Delayed Triggering and Phase Angle with or without Soft Start
- Control Mode: Voltage, Current and Power or V2 and I2 with additional Transfer to VxI
- USB: port integrated for configuration in safety mode (No Load and Auxiliary Voltage needed) Unit Powered Through USB
- 100 kA: Short Circuit Current Rating (SCCR) up to 600V
- Approvals CE+EMC; EAC; cUL from 30A to 500A, UL from 600A to 2100A
Revo PN – Suitable to control Electric Heaters and IR Lamps in Industrial Heating Systems
REVO PN
- Modules of 12 or 24 zones already divided into three phases or one phase from 4 to 24 zones
- Logic input SSR 7÷30Vdc 9mA Max (ON ≥7Vdc OFF <6Vdc)
- L1 - L2 - L3 Power Input 370 - 480V
- Nominal current in continuous service Max 25A for each load
- Max peak current (10ms) 700A
- Nominal Voltage range Ue 24 - 600V
- Isolation Voltage Ui 2500Vac
REVEX 3PH – The Power Controller On Demand
REVEX 3PH
Technical Specification
- Load type: Normal Resistance, Infrared Short, Medium and Long Waveform
- Inputs: 4:20mA, 0:10V, SSR and ModBus as std.
- Firing mode: Burst Firing, Zero Crossing
- Control Mode: Voltage, Current and Power or V2 and I2 with additional Transfer to VxI
- Communication: RS485 port. RTU Modbus® Protocol
- USB: Port integrated for configuration in safety mode (No Load and Auxiliary Voltage needed) Unit Powered Through USB
- Approvals: Comply with CE+EMC / EAC
- Dual Current Limit: For peak and RMS value
- All options are shown below with the relevant model code
- HB Alarm to diagnose partial or Total Load Failure and Thyristor Short Circuit
CD3000S 3PH – From 15A to 90A
CD3000S 3PH
Technical Specification
- Voltage power supply: 24V min, 480V Max, 600V on request
- Input Signal: SSR (OFF state <1Vdc ON = 4÷30 Vdc) firing.
- Firing: Zero crossing ZC.
- Auxiliary Voltage Supply: 10Va power consumption.
- Fan Voltage: 230V ± 15%.
- Approvals:Comply with EMC; cULus available as an option.
- Mounting: Din rail mounting up to 90A.
- Operating Temperature: 0÷40° up to 90A included (for higher temperature see the derating curve)